NOTICE
Note that when converting this document from its original format to a .pdf file,
some minor font and format changes may occur causing slight variations. When
viewing and printing this document, we cannot guarantee that your specific PC or
printer will support all of the fonts or graphics. Therefore, when you view the
document fonts may be substituted and your individual printer may not have the
capability to print the document correctly.

and
System Administration Terminals (SAT)
Technician's Guide
INT-1027 (IPK)
Document Revision 1C
(Applies to Release 1000
through Release 4500)

Contents of this manual are subject to change without prior notice at the discretion of
NEC Unified Solutions, Inc. This document has been prepared for the use of
employees and customers of NEC Unified Solutions, Inc. and may not be
reproduced without prior written approval of NEC Unified Solutions, Inc.
ElectraMail and Electra Elite are registered trademarks of NEC America, Inc.
Windows is a registered trademark of Microsoft Corporation. AT&T is a registered
trademark of AT&T Wireless Services, Inc. Adobe Acrobat Reader is a registered
trademark of Adobe Systems, Inc.
Copyright 2005

NEC Infrontia, Inc.
6535 N. State Highway 161
Irving, TX 75039-2402
Technology Development

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
THIS PAGE INTENTIONALLY LEFT BLANK
___________________________________________________________________________________
iv
Elite IPK SAT Technician's Guide

Introduction
Chapter 1
___________________________________________________________________________________
SEC
TION 1
GENERAL INFORMATION
The System Administration Terminal (SAT) program is a Windows application that
allows the user to easily program and configure many features of the Electra Elite IPK
and Electra Elite 48/192 systems from most any personal computer.
SEC
TION 2
SAT SOFTWARE OVERVIEW
The SAT software allows programming and configuring the Electra Elite IPK system
as well as an Electra Elite 48/192 system (using Series 1000~Series 8000). The
technician only needs this single SAT version installed on their laptop PC to
communicate with either of the KTS systems. SAT makes programming fast and
easy, reducing the overall customizing time to a minimum.
Simply connect the PC (with SAT installed) to the KTS using one of these methods:
Direct connection
Remote connection (via external modem or built-in modem)
LAN/WAN connection
SAT allows all system data to be configured off-line. When programming and
configuration are complete, the data can be uploaded to the main processor. For
system backup, SAT allows the customer's database data to be downloaded to a disk
for safe keeping.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
1 - 1

PC Requirements and Software
Installation
Chapter 2
___________________________________________________________________________________
SEC
TION 1
PC REQUIREMENTS
This section provides the minimum requirements for running the Electra Elite IPK and
Electra Elite 48/192 SAT software.
1.1
PC Requirements
¥
Pentium Processor
¥
Microsoft Windows 95, 98, ME, XP, 2000 or NT 4.0 (or higher) operating
system
¥
At least 15 MB of free hard disk space
¥
Unused PC serial communication port (COM Port)
¥
MNP Class 5 compatible modem (if remote programming is required)
¥
Network Interface Card (NIC) (if programming via LAN/WAN is required)
SEC
TION 2

SOFTWARE INSTALLATION
2.1
Installing Electra Elite System Administration Terminal (SAT)
Software
1.
Insert the SAT Technician setup CD into your CD-ROM drive.
2.
Click the Windows Start button.
3.
Select Run.
4.
Enter d:\Elite IPK SAT TECH.exe and click OK.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
2 - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
5.
Follow the instructions on the PC installation program.

Once the system files have been copied, the installation will prompt with
the install DESI software box. When the box is checked, then DESI will
be installed onto the PC, along with Adobe Acrobat Reader.
SEC
TION 3
STARTING THE SAT PROGRAM FROM A PC
3.1
Starting SAT
1.
Click the Start button.
2.
Select Programs, Electra Elite IPK SAT TECH.
3.
Click Elite IPK SAT.

Figure 2-1 Starting SAT Program
___________________________________________________________________________________
2 - 2
PC Requirements and Software Installation

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
4.
Enter the password. The default password is PASSWORD (in upper
case letters). Click OK.

Figure 2-2 Password Screen
5.
Choose the following KTS type:
¥
<= S7000: used when the system is an Electra Elite 48/192 with
software Series 7000 and below.
¥
S8000: used when the system is an Electra Elite 48/192 with
software Series 8000 only.
¥
IPK: used when the system is an Electra Elite IPK Release 1000
and above.
6.
Click OK.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
2 - 3

PC to KSU Communication
Methods
Chapter 3
___________________________________________________________________________________
There are several ways that a PC can communicate with the Electra Elite 48/192 or
the Elite IPK systems.
r
Direct Connect (Serial Cable)
r
Remote Connection (Built on Modem on the MIFM)
r
Remote Connection (External Modem)
r
LAN/WAN Connection

Note: A modem in the PC or an external modem used must be MNP Class 5.
SEC
TION 1
DIRECT CONNECT
For Direct Connection, a Male straight cable is required. The Electra Elite 48/192
KSU has a Female 25-pin connector on the side of the KSU while the Electra Elite
IPK KSU has a Female 9-pin connector on the side of the KSU. Most personal
computers have a Male 9-pin connector for COM ports.

Figure 3-1 Direct Connection Example
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
3 - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
SEC
TION 2
REMOTE CONNECTION (BUILT-IN MODEM UNIT)
The MIFM Modem Unit must be installed on the MIFM card for proper operation. The
MIFM must be installed in Slot 1 or Slot 2 of the basic cabinet in the Elite 192 or the
Elite IPK, and in Slot 2 of the Elite 48. Programming for the MIFM Modem Unit, via
handset programming, uses Memory Block 1-8-38.
The modem must be assigned a valid extension number of the system's numbering
plan. For example, if station numbers are 500's the modem's number must also be in
the 500's range. There are several ways that the built-in modem unit can be
contacted: via DID to the modem extension, a trunk can be DIT'ed to the modem
extension, or a station or attendant can blind transfer the call to the modem extension.

Telco
Lines
Figure 3-2 Remote Connection (Built-in Modem) Example
SEC
TION 3
REMOTE CONNECTION (EXTERNAL MODEM)
When an external modem is used, a Telco line from Telco can be connected to a SLI
port from the Elite 48/192, or the Electra Elite IPK can be connected to the external
modem. The Null Modem adapter must be used when an external modem is
connected to the Elite 48/192 or Elite IPK. The null modem adapter is provided with
each MIFM ETU.
There are several ways that the external modem unit can be contacted when an SLT
port on the system is used to provide dial tone: via DID to the SLT's modem
extension, a trunk can be DIT'ed to the modem extension, or a station or attendant
can blind transfer the call to the modem extension.
A 25-pin male to 25-pin male straight cable is used when connecting an external
modem to the Elite 48/192. A 9-pin male to 25-pin male is used when connecting an
external modem to the Electra Elite IPK.
___________________________________________________________________________________
3 - 2
PC to KSU Communication Methods

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________

With Remote Connection (External Modem), the MIFM card must reside in the following slots
of the Elite 192 or Electra Elite IPK: ISA, Slot 1 or 2. The MIFM must be installed in Slot 2 in
an Elite 48 KSU.
Telco

Lines
External
Null-modem
Modem
Adapter
Figure 3-3 Remote Connection (External Modem) Example
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
3 - 3

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
SECTION 4
LAN/WAN CONNECTION
When the Elite LAN PC Programming Device is used, the system can be
programmed via the LAN or WAN. Refer to the Installation Instructions on the Elite
LAN PC Programming Device for addition information on setting up the Elite LAN PC
Programming Device using Elite IPK SAT Technician.
Elite LAN PC
Programming Device

Null Adapter
LAN/WAN NETWORK
The type of cable that is used varies depending on the system to which the Elite LAN
Programming device is connected. The Electra Elite IPK uses a DB9 cable and the Electra Elite
48/192 uses a DB-25 cable.
___________________________________________________________________________________
3 - 4
PC to KSU Communication Methods

Configuring the Communication
Methods
Chapter 4
___________________________________________________________________________________
SECTION 1
DIRECT CONNECTION (CONFIGURATION)
When configuring the communication for direct connection, the COM Port speed for
COM 1 of the KSU must match the COM Port speed of the PC. For example, if the
KSU is set for 38.4K bps then SAT must also be set for 38.4K bps. To set the COM
port speed for COM 1 of the KSU, use Memory Blocks 1-8-35 and 1-8-36.
1.1
Setting SAT for Direct Connection
1.
With SAT open, click: COMMUNICATION/SETUP/PC SERIAL PORT.
The following screen will appear:
Figure 4-1 Setup and Initialize Screen
Comm Port: Use this to set the COM port used in the PC to
communicate with the KSU.
Baud Rate: Use this to select the appropriate data transfer speed (must
match the KSU COM port speed).
Line Settings: Use this to select the bits, data, parity, and stop bits
(must match the KSU COM port settings).
The Electra Elite 48/192 and the Electra Elite IPK both support the
following speeds: 4.8K bps, 9.6K bps, 19.2K bps and 38.4K bps.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
4 - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
2.
Once the configuration has been made and all cables are connected,
select the following option from the File Menu: COMMUNICATION/
CONNECT. The following screen will appear:
Figure 4-2 Connection Type Screen
3.
Insure that Direct Connection is selected.
4.
Click the Connect button.
Once the connect button is selected, progress of the connection will be
shown at the bottom of the Connect Screen. Once the connection is
made, this screen automatically disappears. If for some reason the
system communication fails, the reason of failure will be shown at the
bottom of the screen.
___________________________________________________________________________________
4 - 2
Configuring the Communication Methods

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________

The desired COM
Port would not allow
communications to
be established.
Figure 4-3 Example of No Connection
5.
Once communication has been established, proceed to downloading or
uploading the system data.
SEC
TION 2
REMOTE CONNECTION (VIA BUILT-IN MODEM UNIT CONFIGURATION)
When configuring the system for remote connection with a built-in modem unit, the
MIFM with Modem Unit must be located in Slot 1 or 2 of the basic cabinet of the
Electra Elite 192/Electra Elite IPK, and in the Slot 2 of the Electra Elite 48. The PC
must have a working MNP Class 5 Modem. The maximum speed of data transfer rate
for the built-in modem is 19.2K bps.
The modem extension must be assigned to the system before communication can be
established. To assign the modem extension, use Memory Block 1-8-38. The
number assigned here must comply with the system's current numbering plan. There
are several ways of getting a modem call to the built-in modem: by DID calls, DIT'ed
calls, or by Blind Transfer by the Attendant or Station.

If the modem extension is dialed internally, the modem will not answer.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
4 - 3

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
2.1
Configuring SAT to Dial Remotely
1.
With SAT open, click COMMUNICATION/CONNECT. The Connect
Screen appears.
Figure 4-4 Connection Type Screen
2.
Ensure that the Modem Connection button is selected.
3.
Type the number to be dialed in the box below Modem Connection.
4.
Once you have entered the number to be dialed, click Dial.
5.
SAT should initialize the modem and dial the provided number.

SAT uses the dialing properties and location of Windows when
using the modem connection. If needed, changes can be made
from SAT by selecting the SETUP button from the Connect
Screen.
SEC
TION 3
REMOTE CONNECTION (VIA EXTERNAL MODEM CONFIGURATION)
When configuring the system with remote connection using an external modem, the
same System Configuration is used as if it were a direct connect. A SLT port from the
system or a direct line can be plugged into the external modem for analog dial tone.
___________________________________________________________________________________
4 - 4
Configuring the Communication Methods

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Refer to Section 2 Remote Connection (via Built-in Modem Unit Configuration) for
configuring SAT to dial remotely.
SECTION 4
LAN/WAN CONNECTION (CONFIGURATION)
When the LAN/WAN configuration is used, the Elite LAN PC Programming Device
must be installed. For detailed information on how to configure the Elite LAN PC
Programming Device, refer to the Installation for Elite LAN PC Programming
Instructions document.
4.1
Configuring SAT to Communicate via LAN/WAN
1.
With SAT already open click: COMMUNICATION/CONNECT. The
Connection Type screen appears.
Figure 4-5 Connection Type Screen
2.
Ensure that the IP Connection is selected.
3.
From the drop down list chose from the two available options:
J
Direct Ethernet
r
When the Direct Ethernet is selected, click the Setup button.
The Host Setup Screen will appear.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
4 - 5

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
r
This screen allows the IP Address and TCP Port of an
already installed device to be assigned.
172.24.232.76
10001
Figure 4-6 Host Setup Screen
r
Hostname/IP Address: type the IP Address of the Elite LAN
PC Programming Device to contacted.
r
TCP Port Number: type in the assigned TCP port that has
been assigned to the device.

If the device has been contacted previously, the IP
Address will be displayed in the drop down list under
Hostname/IP Address and the TCP port number will be
saved with the IP Address.
J
New Site
When the New Site option is selected, click the Setup button. The
IP Connection Screen will appear. This screen allows the user to
Search/Configure/Update/Ping, and Restore an Elite LAN PC
Programming Device to factory defaults.
Figure 4-7 IP Connection Setup Screen
___________________________________________________________________________________
4 - 6
Configuring the Communication Methods

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
r
Select Site: This allows the user to create a profile for each
device that can be connected to, or to Delete a profile.
r
Current Device Setting: This shows the current device's IP
Address, Subnet Mask, Default Gateway, and TCP Port
Number. If a New Site is selected in the Select Site drop
down list, the Search option can be used to search the
Network for Elite LAN PC Programming Devices in the
following Subnets: Class C and Class B. Once the Search
Button is chosen the following screen will appear.
Figure 4-8 Search for Device Screen
Select the appropriate Subnet that the PC and the Elite LAN PC
Programming Device is located in, and click Search.
Once a device is found, the Device Search Results screen shows
the available device(s) to be configured. If no devices are found, a
message will be displayed stating that no devices were found.
Figure 4-9 Device Search Results Screen
r
Select the device and click OK.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
4 - 7

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
The IP Connection Setup Screen will open with the current Device
Settings.
Figure 4-10 Example of IP Connection Setup
r
Once the Elite LAN PC Programming Device is located
configuration can be performed.
Figure 4-11 IP Connection Setup
___________________________________________________________________________________
4 - 8
Configuring the Communication Methods

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
r
Using the New Device Settings: the following items can be
configured: DHCP Yes or No, IP Address / Subnet Mask /
Default Gateway / TCP Port Number.

If DHCP Service is selected a static IP Address can not
be assigned. When the Use DHCP IP Assignment is
unchecked then the IP Address / Subnet Mask / Default
Gateway options will be allowed.
r
Once the appropriate selections have been made, click the
Update button to update the Elite LAN PC Programming
Device with the new settings.

The Ping option can be used to verify that the device is
able to be reached, the Factory Default button is used
to restore the unit back to default settings.
Once the configuration has be accepted, a confirmation
letting you know that the device was configured successfully
appears.
Figure 4-12 Successful Configuration Screen
r
Click the OK button, and then close the IP Connection
Setup window.
r
Now you are ready to connect to the Electra Elite 48/192 or
Elite IPK System by using the Connect Screen.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
4 - 9

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________

Figure 4-13 Connect Screen
r
In the drop down list, choose the site that was previously
created and click the Connect button.
___________________________________________________________________________________
4 - 10
Configuring the Communication Methods

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
The following information will be displayed to indicate the
system's IP address. Refer to Figure 4-14 IP Address on
Connect Screen.
The IP address of attempted
connection is displayed.
The TCP Port that is being
used is also displayed.
Figure 4-14 IP Address on Connect Screen
r
Once connection is established, proceed with Uploading or
Downloading the system data.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
4 - 11

Migrating from Electra Elite 48/192
to Electra Elite IPK
Chapter 5
___________________________________________________________________________________
SEC
TION 1
GENERAL INFORMATION
The SAT Technician software can use a customer's existing Electra Elite system
configuration and use Electra Elite IPK SAT to convert the Electra Elite database file
to and Electra Elite IPK database.
SEC
TION 2
MIGRATING FROM ELECTRA ELITE 48/192
To migrate from an existing Electra Elite 48/192 system to an Electra Elite IPK R1000
system, Electra Elite IPK System Administration Terminal (SAT) software must be
used to perform this upgrade. The MIFM-U( ) ETU is required for PC Programming
and must be installed prior to performing the migration.
Two methods to access the database from the existing system are explained below:
r
Direct download from the installed system
r
Import the Elite database saved using a previous version of the Electra Elite
SAT
2.1
Direct Download from the Installed Elite System
1.
Verify that the battery is connected to CN4 on Elite192 CPUB( )-U( ) or
Elite 48 MBD-U( ) Unit.
2.
Confirm and record the following settings:
¥
Answer Preset
¥
Automated Attendant/DISA mode
¥
Automatic Trunk-to-Trunk Transfer mode
¥
Automatic Trunk-to-Trunk Transfer Outgoing Trunk
¥
Background Music
¥
Call Forward All Calls, Busy, No Answer, Busy/No Answer,
Centrex/Off-Premise/Split
¥
Callback Messages
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
¥
Customized Message Display
¥
Day/Night Mode (System and Tenant)
¥
Do Not Disturb
¥
MIC Settings
¥
Timed Alarm
The following memories are empty after the upgrade:
¥
Last Number Dialed Memory
¥
Recorded messages in the VRS(4)-U( ) ETUs (messages must be
recorded again)
¥
Store & Repeat/Save & Repeat
3.
Select IPK, enter the password, and click OK to open Electra Elite IPK
SAT.
Figure 5-1 Migrating to Electra Elite IPK - Entering Password
___________________________________________________________________________________
5 - 2
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
4.
From the Communications Menu, select Connect to connect the Elite
system.
Figure 5-2 Migrating to Electra Elite IPK - Connecting to Electra Elite System
5.
When the download is finished, select Save As from the File menu and
enter a file name.
Figure 5-3 Migrating to Electra Elite IPK - Saving a Converted Database
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 3

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
¥
When the system is to be saved as Elite IPK Basic, confirm the
Save As type is Elite IPK Basic (R1000) (*.rdf), and click Save.
¥
Only the Electra Elite 48 system can be saved as Elite IPK Basic.
¥
When the system is to be saved as Elite IPK Expanded, confirm
the Save As type is Elite IPK Expanded (R1000) (*.rdf), and click
Save.
6.
From the Communications menu, select Download and click Start to
download the database from the Electra Elite system.
Figure 5-4 Migrating to Electra Elite IPK - Downloading from Electra Elite System
___________________________________________________________________________________
5 - 4
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
7.
From the Communications menu, select Disconnect to disconnect from
the Electra Elite system.
Figure 5-5 Disconnecting from the Electra Elite System
8.
Assign any other required system data assignment changes, then select
Save from the File menu, if required.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 5

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
9.
Change hardware from the Electra Elite system to the Electra Elite IPK
system. Refer to Table 5-1 Upgrading Hardware from Electra Elite to
Electra Elite IPK.
Table 5-1 Upgrading Hardware from Electra Elite to Electra Elite IPK
Upgrade Type
Comments
Electra Elite 48 to Electra Elite IPK Basic
Replace the B48 -U10 KSU hardware with:
Port Package
· B64-U20 KSU
· CPUI( )-U( ) ETU (without PKU 192-U)
· ESI(8)-U( ) ETU in Slot 1,
· Move all other hardware to new KSU
Electra Elite 48 to Electra Elite IPK
Replace the B48 -U10 KSU hardware with:
Expanded Port Package
· B64-U20 KSU
· CPUI( )-U( ) ETU (with PKU 192-U)
· ESI(8)-U( ) ETU in Slot 1,
· Move all other hardware to new KSU
Electra Elite 192 to Electra Elite IPK Basic
Not supported
Port Package
Electra Elite 192 to Electra Elite IPK
· Replace the B64-U10 KSUs with B64-U20 KSUs
Expanded Port Package with new IPK
· Replace all CPUB( )-U( ) ETUs with
KSUs
CPUB( )-U( ) ETU with PKU 192-U
· Move all other hardware to new KSUs
Electra Elite 192 to Electra Elite IPK
· Replace all CPUB( )-U( ) ETUs with CPUI( )-U( )
Expanded Port Package without new IPK
ETU with PKU 192-U
KSUs (Retrofit)
,The ESI(8)-U( ) or ESIB-U( ) ETU
___________________________________________________________________________________
5 - 6
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
10.
From the Communications menu, select Connect to connect to the
Electra Elite IPK system.
Figure 5-6 Connecting to the Electra Elite IPK System
11.
From the Communications menu, select Upload and click Start.
Figure 5-7 Uploading to the Electra Elite IPK System
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 7

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
12.
Click Hardware Upload.
Figure 5-8 Uploading Hardware to the Electra Elite IPK System
13.
When the upload is complete, click Close.
Figure 5-9 Upload Complete Screen
___________________________________________________________________________________
5 - 8
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
14.
From the Communications menu, select Disconnect to disconnect from
the Electra Elite IPK.
Figure 5-10 Migrating to Electra Elite IPK - Disconnecting from Electra Elite System
15.
Reassign all settings recorded in Step 2, and confirm proper system
operation.
SEC
TION 3
IMPORTING THE ELECTRA ELITE DATABASE SAVED USING A PREVIOUS
VERSION OF THE ELECTRA ELITE SAT
1.
Verify that the battery is connected to CN4 on Elite192 CPUB( )-U( ) or Elite 48
MBD-U( ) Unit.
2.
Confirm and record the following settings:
J
Answer Preset
J
Automated Attendant/DISA mode
J
Automatic Trunk-to-Trunk Transfer mode
J
Automatic Trunk-to-Trunk Transfer Outgoing Trunk
J
Background Music
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 9

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
J
Call Forward All Calls, Busy, No Answer, Busy/No Answer, Centrex/
Off-Premise/Split
J
Callback Messages
J
Customized Message Display
J
Day/Night Mode (System and Tenant)
J
Do Not Disturb
J
MIC Settings
J
Timed Alarm
The following memories are empty after the upgrade:
J
Last Number Dialed Memory
J
Recorded messages in the VRS(4)-U( ) ETUs (messages must be
recorded again)
J
Store & Repeat/Save & Repeat
3.
Select IPK, enter the Password. Click OK to open Electra Elite IPK SAT.
Figure 5-11 Importing a Database to Electra Elite IPK - Entering Password
___________________________________________________________________________________
5 - 10
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
4.
From the File Menu, select Import Elite file to import a previously saved
database.
Figure 5-12 Importing a Database to Electra Elite IPK - Importing an Elite File
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 11

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
5.
Locate the directory where the Elite database is stored. Select the file name and
click Open to import the database.
Figure 5-13 Importing a Database to Electra Elite IPK - Opening an Imported File
6.
When the download is finished, select Save As from the File Menu and enter a
file name.
·
When the system is to be saved as Elite IPK Basic, confirm that Save as
type is Elite IPK Basic (R1000) (*.rdf), and click Save.

Only the Electra Elite 48 system can be saved as Elite IPK Basic.
___________________________________________________________________________________
5 - 12
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________

Figure 5-14 Importing a Database to Electra Elite IPK - Saving Elite IPK Basic File
·
When the system is to be saved as Elite IPK Expanded, confirm that Save as
type is Elite IPK Expanded (R1000) (*.rdf) and click Save.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 13

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________

Figure 5-15 Importing a Database to Electra Elite IPK - Saving Elite IPK Expanded File
7.
Assign any other required system data assignment changes and from the File
menu, select Save if required.
8.
Change hardware from the Elite System to the Electra Elite IPK system. (Refer
to Table 5-2 Upgrading Hardware from Electra Elite to Electra Elite IPK.
Table 5-2 Upgrading Hardware from Electra Elite to Electra Elite IPK
Upgrade Type
Comments
Electra Elite 48 to Electra Elite IPK Basic
Replace the B48 -U10 KSU hardware with:
Port Package
· B64-U20 KSU
· CPUI( )-U( ) ETU (without PKU 192-U)
· ESI(8)-U( ) ETU in Slot 1,
· Move all other hardware to new KSU
Electra Elite 48 to Electra Elite IPK
Replace the B48 -U10 KSU hardware with:
Expanded Port Package
· B64-U20 KSU
· CPUI( )-U( ) ETU (with PKU 192-U)
· ESI(8)-U( ) ETU in Slot 1,
· Move all other hardware to new KSU
Electra Elite 192 to Electra Elite IPK Basic
Not supported
Port Package
___________________________________________________________________________________
5 - 14
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Table 5-2 Upgrading Hardware from Electra Elite to Electra Elite IPK (Continued)
Upgrade Type
Comments
Electra Elite 192 to Electra Elite IPK
· Replace the B64-U10 KSUs with B64-U20 KSUs
Expanded Port Package with new IPK
· Replace all CPUB( )-U( ) ETUs with
KSUs
CPUB( )-U( ) ETU with PKU 192-U
· Move all other hardware to new KSUs
Electra Elite 192 to Electra Elite IPK
· Replace all CPUB( )-U( ) ETUs with CPUI( )-U( )
Expanded Port Package without new IPK
ETU with PKU 192-U
KSUs (Retrofit)
,The ESI(8)-U( ) or ESIB-U( ) ETU
9.
From the Communications menu, select Connect to connect to the Electra Elite
IPK.
Figure 5-16 Importing a Database to Electra Elite IPK - Connecting to Electra
Elite IPK System
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 15

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
10. From the Communications Menu, select Upload and click Start.
Figure 5-17 Importing a Database to Electra Elite IPK - Uploading to Electra Elite IPK
System
11.
Click Hardware Upload.
Figure 5-18 Importing a Database to Electra Elite IPK - Uploading Hardware to
Electra Elite IPK System
___________________________________________________________________________________
5 - 16
Migrating from Electra Elite 48/192 to Electra Elite IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
12. When Upload is finished, click Close.
Figure 5-19 Importing a Database to Electra Elite IPK - Upload Complete
13. From the Communications menu, select Disconnect to disconnect from the
Electra Elite IPK.
Figure 5-20 Importing a Database to Electra Elite IPK - Disconnecting from
Electra Elite IPK System
14. Reassign all settings recorded in Step 2 and confirm proper system operation.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
5 - 17

Electra Elite S8000 Upgrade
Procedure for Electra Elite 48/192
Chapter 6
___________________________________________________________________________________
SEC
TION 1
MIGRATION FROM S7000 AND BELOW
Use the following instructions to migrate from an existing Series 7000 and below
Electra Elite 48/192 system, to a Series 8000 Electra Elite 48/192 system.
The Electra Elite IPK System Administration Terminal (SAT) software must be used to
perform this upgrade. The MIFM-U( ) ETU is required for PC Programming and must
be installed.
SEC
TION 2
UPGRADING TO S8000 USING A DIRECT DOWNLOAD FROM THE INSTALLED
SYSTEM
1.
Confirm and record all of the following settings in the system. These settings will
need to be manually re-entered into the system after the upgrade:
·
Answer Preset (Ringing Line Preference)
·
Automated Attendant/DISA mode
·
Automatic Trunk-to-Trunk Transfer mode
·
Automatic Trunk-to-Trunk Transfer Outgoing Trunk
·
Background Music
·
Call Forward Settings (Call Forward - All Calls, Busy, No Answer, Busy/No
Answer, and Call Forward - Centrex/Off-Premise/Split)
·
Callback Messages
·
Customized Message Display
·
Day/Night Mode (System and Tenant)
·
Do Not Disturb
·
MIC Settings
·
Time d Alarm
The following memories will be empty after the upgrade:
·
Last Number Dialed Memory
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
6 - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
·
Recorded messages in the VRS(4)-U10 ETU's

The recorded messages will need to be rerecorded
·
Store & Repeat/Save & Repeat
2.
Open Electra Elite IPK SAT by selecting S8000 and entering the Password.
Figure 6-1 Opening Electra Elite IPK SAT
3.
From the Communications menu, select Connect to connect to the Elite IPK
system.
___________________________________________________________________________________
6 - 2
Electra Elite S8000 Upgrade Procedure for Electra Elite 48/192

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________

Figure 6-2 Connecting to the KTS
4.
From the Communications menu, select Download to retrieve the database
from the Elite IPK system.
Figure 6-3 Downloading the Database
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
6 - 3

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
2.1
Electra Elite 48 Upgrade
Proceed with the following steps to upgrade an Electra Elite 48 system.
1.
When the download is finished, from the File menu, select Save as...
and enter a file name. If the system is to be saved as an Elite 48,
confirm the Save as type is: Elite 48 (S8000)(*.rdf).

An Elite 192 system cannot be saved as an Elite 48 system.
Figure 6-4 Save As Screen for Elite 48 System
___________________________________________________________________________________
6 - 4
Electra Elite S8000 Upgrade Procedure for Electra Elite 48/192

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
2.
From the Communications menu, select Disconnect to disconnect from
the Elite system.
Figure 6-5 Disconnecting from the Elite KTS
3.
Power off the KSU.

Be sure you have logged the information in Section 2, step 1.
4.
Disconnect the battery from connector CN4.
5.
Install the Elite 48 V8.XX EPROM in IC5 on the backplane.

When upgrading from V8.XX to a higher version V8.XX, Steps 6 and 7
are not required.
6.
Remove security chip KCS(1.0, 2.0, 3.0, 4.0, 5.0, 6.0 or 7.0)U from IC30.
7.
Install KCS(8.0)U chip in IC30.
8.
Place dip switches SW1-1 and SW1-2 ON (for flash ROM load from
EPROM), and place SW3-1 ON (for system boot from EPROM).
9.
Power on the KSU. The CPU Live LED will be flashing.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
6 - 5

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
10.
After CPU Live LED goes off (approximately 1 minute), power off the
KSU.
11.
Remove the EPROM and place dip switches SW1-1, SW1-2, and SW3-1
OFF.
12.
Power on the KSU.
13.
After the system comes up, reconnect the battery to connector CN4.
A
14.
From any display telephone press
and dial C to check the
revision. When SP018 V8.XX is displayed on the second row of the
LCD, the upgrade is complete.
For Elite 48, proceed to Section 2.3 Proceeding with Upgrade.
2.2
Elite 192 Upgrade
Proceed with the following steps to upgrade an Electra Elite 192 system.
1.
When the download is finished, from the File menu, select Save as...
and enter a file name. Confirm the Save as type is: Elite 192
(S8000)(*.rdf).
Figure 6-6 Save As Screen for Elite 192 System
___________________________________________________________________________________
6 - 6
Electra Elite S8000 Upgrade Procedure for Electra Elite 48/192

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
2.
From the Communications menu, select Disconnect to disconnect from
the Elite system.
Figure 6-7 Disconnect Screen
3.
Power off the KSU.

Be sure you have logged the information in Section 2, step 1.
4.
Disconnect the battery from connector CN4.
5.
Install the Elite 192 V8.XX EPROM in IC5 on the CPU card.

When upgrading from V8.XX to a higher version V8.XX, Steps 6 and 7
are not required.
6.
Remove security chip KCB(1.0, 2.0, 3.0, 4.0, 5.0, 6.0 or 7.0)U from IC30.
7.
Install KCB(8.0)U chip in IC30.
8.
Place dip switches SW1-1 and SW1-2 ON (for flash ROM load from
EPROM), and place SW3-1 ON (for system boot from EPROM).
9.
Power on the KSU. The CPU Live LED is flashing.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
6 - 7

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
10.
After CPU Live LED goes off (approximately 1 to 3 minutes), power off
the KSU.
11.
Remove the EPROM and place dip switches SW1-1, SW1-2, and SW3-1
OFF.
12.
Power on the KSU.
13.
After the system comes up, reconnect the battery to connector CN4.
A
14.
From any display telephone, press
and dialCto check the
revision. When SP018 V8.XX is displayed on the second row of the
LCD, the upgrade is complete.
2.3
Proceeding with Upgrade
1.
Assign any other required system data assignment changes and from
the File menu, select Save, if required.
2.
From the Communications menu, select Connect to connect to the Elite
system.

Figure 6-8 Connecting to the Elite KTS
___________________________________________________________________________________
6 - 8
Electra Elite S8000 Upgrade Procedure for Electra Elite 48/192

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
3.
From the Communications menu, select Upload and click the Start
button.
Figure 6-9 Beginning the Upload Process
4.
Click the Hardware Upload button.
Figure 6-10 Hardware Upload Screen
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
6 - 9

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
5.
When the Upload is finished, Click the Close button.
Figure 6-11 Pressing the Close Button
6.
From the Communications menu, select Disconnect to disconnect from
the Elite system.
Figure 6-12 Disconnecting from the Elite System
___________________________________________________________________________________
6 - 10
Electra Elite S8000 Upgrade Procedure for Electra Elite 48/192

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
7.
Reassign all the settings recorded in Section 2 Upgrading to S8000
using a Direct Download from the Installed System on page 6-1, and
confirm proper system operation.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
6 - 11

Programming Screens
Chapter 7
___________________________________________________________________________________
SEC
TION 1
MAIN MENU
When the SAT software program is launched, the Main Menu screen is displayed first.
This screen allows the user to access the options used to program the Electra Elite
system. Refer to Figure 7-1 Electra Elite SAT Software Screen Main Menu for a
description of this screen.
Pulldown menus
File Name
System Size
Mode of SAT Operation
Help Access
Toolbar
Connection Status - Indicates if
data path is established to the
KTS
Figure 7-1 Electra Elite SAT Software Screen Main Menu
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
SEC
TION 2
PULLDOWN MENU
Pulldown menus are available for each function involved in programming the Electra
Elite IPK system. To access the data associated with the function, click on the
function name on the Main Menu. Some of the options on the initial pulldown menu
offer several selections. An arrow to the right of the option name indicates that
additional selections are available. Refer to Figure 7-2 Pulldown Menu Example.
Click arrow for additional
information
Click menu
choice to display
screen
Figure 7-2 Pulldown Menu Example
___________________________________________________________________________________
7 - 2
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
SEC
TION 3
SYSTEM DATA SCREEN
When an option is selected from a pulldown menu, a screen is displayed that allows
the user to program data for the function selected. Refer to Figure 7-3 Example of a
System Data Screen.
Screen tabs indicate system data items that are grouped together for programming.
The active tab group is indicated by a box around the tab title. To access another tab
group, press the tab or use the keyboard shortcut. Keyboard shortcuts are displayed
at the bottom of the screen in the Information Bar.
Tabs
Keyboard Shortcut
Information Bar
Figure 7-3 Example of a System Data Screen
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 3

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
SEC
TION 4
TOOLBAR ICONS
This section explains the toolbar icons that allow the user to easily navigate the
program.
The availability of the individual tools depends on the activity the user is performing.
When the icon appears shadowed, the tool is not available. When the icon is dark,
the tool is available. The toolbar icons are listed and shown below.
Creates new customer configuration file.
Loads or opens an existing customer configuration
file.
Saves the customer configuration file to the hard disk
or floppy disk.
Accesses the Job Specifications printing option.
Accesses the wizard for individual features. The F10
special function key provides a shortcut to this
wizard.
Sets the defaults for all items on the open tab.
Sets the defaults for the individual system data items
(on the screen the default is set for the item where
the cursor is blinking).
Allows data items to be copied between ports. The
F3 special function key provides a shortcut to this
feature.
Allows values between two ports to be swapped. The
F5 special function key provides a shortcut to this
feature.
___________________________________________________________________________________
7 - 4
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Allows the user to undo the current edits and return
to the previous editing operation.
Allows the user to return to the previous editing
operation. The F11 special function key provides a
shortcut to this feature.
Accesses Quick Search. Quick Search provides a
detailed list of system data items. The F8 special
function key provides a shortcut to this feature.
Returns to the previous tab group. The Shift + F6
special function key provides a shortcut to this
feature.
Advances to the next tab group. The F6 special
function key provides a shortcut to this feature.
Displays the help contents for the Electra Elite IPK
SAT End-User software program. The F1 special
function key provides a shortcut to this feature.
Scrolls up displaying the previous page.
Scrolls down displaying the next page.
Advances to the first page.
Advances to the last page.
Brings up the Connection dialog box. The F7 special
function key provides a shortcut to this feature.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 5

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
SEC
TION 5
ELECTRA ELITE SAT PULLDOWN MENUS
This section explains each available pulldown menu in the Electra Elite SAT software.
File
The File pulldown menu provides options for basic file management.
New
Creates a new configuration file.
Open
Loads an existing configuration.
Save
Saves the configuration file. This option is only available when a configuration file is
open.
___________________________________________________________________________________
7 - 6
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Save As
Saves a configuration file using a new name. This option is only available when a
configuration file is open.
Import Elite File
This option is available in the S8000 and IPK mode only. Use this option to import
existing files to the appropriate software that is selected.
Convert to IPK
This option is available in the S7000 and S8000 mode. Use this option to convert
existing files to the appropriate software that is selected.
Convert to S8000
This option is only available in S7000. Use this option to convert existing files to
S8000.
Close
Used to close the current configuration file. This option is only available when a
configuration file is open.
Wizard
Used to access the Wizard feature. Wizard is available for every feature in the
Electra Elite system and provides all information to program a feature. All data items
for programming the feature are grouped together. The user can press a tab to
access system data and make the necessary changes. This option is only available
when a configuration file is open.
Change Password
Allows the user to change the SAT password. When the password is changed it will
effect all modes.
Print
Provides two print options: Job Specifications and Designation Labels (requires a
standard inkjet or laser printer). When Job Specifications is selected, a menu is
displayed with three print options for the Job Specifications. Print a family (group)
such as system-wide, trunk group, or tenant or one of a range of Memory Blocks.
When Designation Labels is selected, SAT automatically opens the DESI for
Windows label printing application. The current telephone information is
automatically exported to DESI. Labels can then be configured and printed for the
telephones. DESI requires the NEC LASER Labels for printing on InkJet or Laser
printers.

To enable the Designation Labels option, the DESI for Windows application must be installed
on your computer. Installation is usually done during the installation of SAT.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 7

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
Print Setup
Allows access to the printer setup screen. This allows the printer configuration to be
modified.
Recent File
Displays the last two files that were opened, these are listed as 1 and 2. The user can
select either file to open. This option is only available when New or Open is selected.
Exit
Exits the programming software. When changes have not been saved, the technician
is prompted to save the changes before the program shuts down.
___________________________________________________________________________________
7 - 8
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Edit
The Edit pulldown menu allows files to be edited or swapped.
Undo
Allows the user to undo current edits and return to previous editing.
Copy
Used to copy port information from one port to another.
Swap
Allows values to be swapped between two ports.
Set Default
Defaults to the current field where the cursor is positioned.
Set Default All
Allows the user to set all values to default on the open tab.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 9

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
Quick Search
Allows a search for Memory Block Number, Name, or Tab Name using a list. The user
can click a Memory Block and modify necessary System data.
Basic
The Basic pulldown menu allows access to basic programming items.

Some menu items may be disabled when the appropriate hardware is not assigned, or a
dependent data item is not set.
System Configuration
This option allows the technician to configure the customer system by indicating the
cards that are installed for each slot in the KSU.
Terminals
This option allows the technician to assign the terminals to the system.
Several selections are available with this option:
___________________________________________________________________________________
7 - 10
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
J
System Wide
J
Station Base
J
Multiline
J
Single Line
J
DSS/BLF
J
Doorphones
J
Display Board
CO/PBX Trunks
This option allows technicians to program system data related to trunk assignments.
Three selections are available with this option:
J
System Wide
J
Trunk Base
J
Timers
Intercom
This option allows the technician to program system data related to intercom
assignments.
DISA
This option allows the technician to assign codes for Direct Inward System Access
(DISA).
Paging
This option allows data related to paging assignments to be programmed.
Access Codes
This option allows the technician to enter Access Codes. Where appropriate, Access
Codes are set to default system values.
Speed Dialing
This option allows data related to system and station speed dialing to be
programmed.
System Timers
This option allows system-wide timers to be assigned.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 11

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
Tenants
This option allows data related to tenant assignments to be programmed.
Call Arrival Keys
This option allows Call Arrival block assignments to be programmed.
Forced Account Code
This option allows the technician to program the account code length and to assign
account codes.
___________________________________________________________________________________
7 - 12
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Application
The Application pulldown menu allows access to system data items relating to
advanced system applications.
Automatic Route Selection
This option allows Automatic Route Selection (ARS) to be programmed.
Code Restriction
This option allows code restriction assignments to be programmed.
SMDR
This option allows data related to Station Message Detail Recording (SMDR) to be
programmed.
Tandem Transfer
This option allows the assignment of data related to the routing of a call through the
system.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 13

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
TLI/DID
This option allows data related to Tie Lines and Direct Inward Dialing to be
programmed. Three selections are available with this option:
J
Trunk Base
J
Networking
J
Timers
DTI/T1
This option allows data related to the master clock and T1 signaling formats to be
programmed.
ACD/UCD
This option allows the technician to set up Automatic Call Distribution and Uniform
Call Distribution Hunt groups.
Voice Mail
This option allows data related to the internal voice mail to be programmed.
VRS/Delay Announcement
This option allows data to be assigned for the VRS ETU (e.g., greetings).
Automated Attendant
This option allows the technician to program the data related to messaging.
Caller ID
This option allows Caller ID displays to be programmed and display assignments to
be assigned per port.
ISDN/BRT
This option allows the assignment of information related to ISDN/BRT trunks such as
SPID assignments, IDSN telephone numbers, and BRT/DTMF duration.
ISDN Call by Call
This option allows call by call service to be programmed.
PHS
This option allows operation of the Dterm PS II.
Emergency Service
This option allows E-911 outgoing.
___________________________________________________________________________________
7 - 14
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
CCIS Networking
This option allows the assignments of information related to K-CCIS.
IP Phones
This option allows operation of the Dterm IP Stations.
HUB
This option allows the assignments of information related to the in skin hub card.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 15

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
Users
The Users pulldown menu allows access to system data items related to speed
dialing.
Speed Dialing
This option allows the technican to program Feature Access Keys, One Touch Keys,
System Speed Dials, and Station Speed Dials for each Multiline Terminal in the
Electra Elite system.
Call Forward/DND
This option allows the technician to program Call Forward/DND and Call Forward
Split.
Misellaneous
This option allows the technician to program Day/Night/Weekend Mode, Station Base
Settings, and Trunk Base Settings.
___________________________________________________________________________________
7 - 16
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Communications
The Communications pulldown menu allows access to system data items relating to
direct and remote connections to the Electra Elite system.
Connect
This option allows the technician to connect to the Electra Elite system, after a
successful connection is established with the KTS, you can upload and download
data to and from the KTS.
Disconnect
This option allows the technician to disconnect from the Electra Elite system.
Upload
This option allows the technician to upload programming changes and configurations
to the KTS.
Download
This option allows the technician to download the current Electra Elite configuration.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 17

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
Verify
This option allows the technician to compare the configuration programmed in the
KTS with that of the PC.
First Initialization
This option reinitializes the system to the factory defaults.

All active calls on the system are dropped.
Second Initialization
This option reboots the system without resetting the programmed defaults (i.e., all
programming is retained).
Setup
This option allows the technician to set up the system to provide communication.
Four options are available for this selection:
J
PC Serial Port - serial port of the PC that is connected to the KTS.
J
Access Password - the password programmed in Memory Block 1-8-17 on the
KTS.
J
Site Name - the name of the site that is being programmed.
J
Setup & Initialize - the KTS port settings/configurations.
___________________________________________________________________________________
7 - 18
Programming Screens

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
Help
The Help pulldown menu allows access to online help.
Using Help
This option provides access to the help topics window that describes how to use the
help function.
Contents
This option provides access to the help topics that are available for the Electra Elite
IPK System Administration Terminal system.
Help Topics
This option provides a list of help topics. The user can bookmark topics to refer to
again.
Show MB Numbers
When the cursor is positioned over a data field, the memory block number is
displayed above the cursor (Show MB Numbers must be selected).
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
7 - 19

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
About
This option provides information about the System Administration Terminal software
(SAT) and the KTS software revision.
Release 1.00 [11035] - This is the released version of Electra Elite IPK
SAT and the Build Number of SAT.
SP1011 1.00 51
Database version of the CPU
Defines the actual version of CPU software
Defines the Release Series in use
Defines the type of Key System:
1 = Basic or 48
3 = Expanded or 192
Defines which Country the software is to be
utilized for:
0 = United States
1 = Japan
2 = Asia
3 = Australia
Identifies System Type
1 = Elite IPK System
0 = Electra Elite 48/192 System
___________________________________________________________________________________
7 - 20
Programming Screens

Special Features of SAT IPK
Chapter 8
___________________________________________________________________________________
SEC
TION 1
GENERAL INFORMATION
This Chapter describes the special features that SAT has to offer. These features
allow for quick and simple system programming and customizing.
SEC
TION 2
SPECIAL FEATURES
Each of the SAT Special Features are described next:
r
Wizards organize system data assignments to program single features. When
the user selects Wizard, the system provides a list of information related to the
selected feature.
r
Multiple Assignments of Station Numbers allows a range of station numbers
to be assigned with a few clicks.
Example Scenario:
System with 96 stations with Station
Numbers 100-195 need to be changed to
200-296.
Example Operation:
Change Station port 01 to 200. In the
Multiple Assignment box, enter 96 ports and
click "Assign".
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
8 - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
r
Copy/Swap allows information from one Station or Trunk to be copied to
multiple Stations or Trunks.
Copy Operation
Example Scenario:
A system of 120 stations recently requests that the Hands
Free feature be activated.
Example
Change MB 4-29 to "YES" for station port 01. Initiate the
Operation:
Copy feature of SAT by pressing F3, clicking on the Copy
Icon, or clicking on the Edit Menu and choosing "Copy".
Make sure that MB 4-29 is highlighted. Make sure that port
01 is marked with "F". This represents that copying is
FROM that port. Make sure that all of the other ports you
want to copy MB 4-29 to are marked with "T".
In this example we will be marking ports 02~120 with "T".
Click the "Copy" button, and now MB 4-29 has been copied
from port 01 to ports 02~120.

Swap Operation
Example Scenario:
A customer has two users that have swapped offices. The
users have completely different characteristics assigned to
their phones. The customer would like for the users to take
their phones with them to their new office and retain all the
original phone characteristics.
Example
Select any TAB that contains a MB beginning with Mode 4
Operation:
(for Telephone Mode). Select the Swap function by
pressing F5, clicking on the Swap Icon, or clicking on the
Edit Menu and choosing "Swap". Enter the two station
port numbers that you wish to swap, and then click the
"Swap" button. Now all of the data has been swapped for
the two terminals.
___________________________________________________________________________________
8 - 2
Special Features of SAT IPK

Electra Elite IPK
Document Revision 1C
___________________________________________________________________________________
r
CAP Key Auto Assign allows the technician to copy/assign multiple CAP keys
to other Multiline Terminals.
CAP Key Auto Assign Example
Example Scenario:
A customer wants to remove the direct CO appearances
from their telephones and give each telephone four Call
Appearance Keys.
Example
In Line Key Assignment for Stations, MB 4-12, assign four
Operation:
CAP keys (C00-01~C00-04) on line keys 1~4. Click the
"CAP Key Auto Assign" Key. You now can assign CAP
keys using two methods:
1. Sequential Assignment will maximize the number of
CAP keys assigned by assigning as many keys per
block to each station, keeping each individual station's
keys within the same block.
2. CAP Block to Port Assignment will assign each station
its CAP keys from a different CAP Block. Choose the
method you wish to use, and select the TO and FROM
assignments for each station port that will have CAP
keys assigned. The Station to Call Appearance Block
Assignment (MB 4-43) will also be correctly assigned for
you.
r
ARS Simulator allows the tech to confirm that the dialing number is programmed
correctly in Automatic Route Selection.
r
Multiple Assignment of Forced Account Codes, allows the account multiple
account codes to be assigned.
r
Moving/Replacing Hardware, allows for cards to be moved/replaced while
maintaining the assigned data to the trunks or stations. See Appendix A for
details.
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
8 - 3

Moving/Replacing Cards
Appendix A
___________________________________________________________________________________
Two operations have been added to SAT IPK regarding moving and replacing cards
using SAT.
r
Moving A Card - Moving a card from one slot to another slot.
r
Replacing A Card - Replacing a card with a new card in the "Card Shelf".
This chapter explains these two operations in detail. These two operations apply to
all modes (S7000, S8000, and R1000) in the Elite IPK SAT.
Refer to Figure A-1 Slot Interface Assignment Screen for a detailed view of how the
cards are assigned in the KSU.
Cabinets
Card Shelf
Slots
Figure A-1 Slot Interface Assignment Screen
___________________________________________________________________________________
Elite IPK SAT Technician's Guide
A - 1

Document Revision 1C
Electra Elite IPK
___________________________________________________________________________________
SEC
TION 1
MOVING A CARD
Purpose:
To keep all related settings when a card is moved from one slot to another slot. For
example, when a user moves an ESI8 card from slot 1 to slot 5, then the data in
MB 7-02, 1-2-08, 2-06, 4-xx will remain intact.
It is possible, when a card is moved around, some settings are reset to default values.
Also if you delete a card, in previous version of SAT, some settings will be reset to
default values.
Operation:
Point your mouse to a card in a cabinet, press the left mouse button, move and drop
this card to a new slot.

DO NOT release the left mouse button when you see a "trash bin" . Releasing the left mouse
button when the trash bin appears means "deleting" a card.
SEC
TION 2
REPLACING A CARD
Purpose:
To keep all related settings when a card is replaced with a card of the same type.
For example, when a user drags an ESIB16 and drops it over an ESI8 in a cabinet,
the first 8 ports of data in MB 7-02, 1-2-08, 2-06, 4-xx will remain intact. Data related
to the last 8 ports will take default values.
The following cards in each category are of the same type:
r
Category 1 - Cards with TEL port type ESI and ESIB
r
Category 2 - Cards with SLT port type SLI and OPX
r
Category 3 - Cards with CO port type COI and COID
r
Category 4 - DTI cards DTI 4, DTI 8, DTI 12~DTI 24
r
Category 5 - PRT cards PRT 4, PRT 8, PRT 12~PRT24
A Card not listed in any of the categories above has its own category by itself.
Operation:
Select a card in the "card shelf", drag it over an existing card in a cabinet, and drop it
in by releasing the mouse button.
___________________________________________________________________________________
A - 2
Moving/Replacing Cards

and
SYSTEM ADMINISTRATION TERMINAL (SAT)
TECHNICIAN'S GUIDE
NEC Unified Solutions, Inc.
Document Revision 1C
(Applies to Release 1000
through Release 4500)

Document Outline